Spicer Dana LMS Hub Assembly Procedure Instrukcja Użytkownika Pobierz pdf

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub.

This may result in a seal or bearing failure, which may result in loss of wheel end and or loss of vehicle control.

04/03 1 of 11 ABIB-0302

Spicer



Axles & Brakes

ABIB-0302

Information Bulletin

Bulletin Type: Parts / Service Information

Topic: Dana LMS™ Hub Assembly Procedure – Steer and Drive Axles

Note: Bulletin ABIB-0302 replaces the original bulletin ABIB-9606.

The Dana LMS™ hub design eliminates bearing adjustment and variables that cause excessive endplay leading to

premature wheel seal failures.

The Dana LMS™ hub design combines proven seal technology with precision-manufactured bearing spacers and special

tolerance bearings.

The Dana LMS™ Hub is available on the following Steer and Drive Axle Models:

Steer Axles:

E-1000I E-1202I E-1462I

E-1200I E-1460I E-1320I

Drive Axles:

All “R” series spindles only.

WARRANTY COVERAGE

Installation of the LMS™ Hub requires certification by Dana. The Dana LMS™ Hub is covered for 3 years/350,000 miles for

On/ Off-Highway applications, when installation is performed by certified installers, and Dana approved synthetic lubes are

used.

CAUTION: The wheel seal cannot be reused. Any time the hub is removed from the spindle, the seal must be

replaced. Failure to follow this requirement will void warranty.

1 2 3 4 5 6 ... 10 11

Podsumowanie treści

Strona 1

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 2 - PARTS INFORMATION

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 3 - INSTALLATION PROCEDURE

04/03 11 of 11 Copyright Dana Corporation, 2003 Printed in USA

Strona 4

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 5

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 6

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 7 - Steer Axles

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 8 - Drive Axles

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 9

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 10 - Visual Inspection

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Strona 11 - Functional Checks

WARNING: Do not attempt to make LMS™ hubs by using LMS™ bearing, spacer and seals in a standard hub. This may result in a seal or bearing failure,

Komentarze do niniejszej Instrukcji

Brak uwag